Blast and Repaint - MV Tramp Workboat

Revamp the Tramp

In April 2015 we abrasive blasted and repainted Neumann Plant division’s work boat MV Tramp. 

The “Tramp” was blasted with Crushed Glass in our 15 metre by 7 metre by 7 metre Abrasive Blasting Booth then repainted in our 20 x 20 metre Spray booth. 

Paint used was Wattyl PR250 primer, Wattyl Epinemal DTM985 High build epoxy and a Wattyl Poly U 400 Topcoat. Jotun Anti foul was also used.

See other recent Abrasive Blasting and Industrial Coatings Projects.

Find out more about Neumann Contractors - Abrasive BlastingIndustrial Coatings.

Wattyl – Epinamel PR250 – Epoxy Primer
Product Description:

  • a universal two pack adhesion promoting, polyamide cured epoxy primer,
  • approved to APAS-2971,
  • conforms to AS/NZS 3750.13 Type 2 and 3,
  • FDA Food Contact Compliant.

Principal Characteristics:

  • general purpose epoxy primer in protective coating systems
    for steel and non-ferrous metals
  • excellent adhesion to steel, galvanized steel, non-ferrous
    metals and fibreglass
  • excellent flow and wetting properties
  • excellent water and corrosion resistance
  • cures at temperatures down to +5°C
  • suitable for touching up of weld seams and damages of
    epoxy coatings during construction
  • long recoating intervals are possible when overcoating with
    epoxy and polyurethane coatings
  • can be overcoated with most alkyd, chlorinated rubber,
    epoxy, two component polyurethane and catalysed acrylic
  • suitable on wet blast cleaned substrates (damp or dry)
  • suitable primer for immersion systems (in fresh and salt
    water) when applied over suitably prepared surfaces
  • suitable with well designed cathodic protection systems
  • suitable for use as a prefabrication primer (Olive Green
    only) (refer to Technical Data Sheet P30.07 for details)
  • cure with Epinamel EH100 standard hardener or Epinamel EH120 low temperature hardener

Wattyl – Epinamel DTM985 – Epoxy
Product Description:

  • a two component surface tolerant high solids, direct to metal high build polyamine adduct cured epoxy coating,
  • approved to APAS 2973,
  • conforms to AS/NZS 3750.14,
  • conforms to AS/NZS 4020:2005 factory made white only

Principal Characteristics:

  • maintenance coating for use in a wide range of industrial applications as a primer, build coat or finish coat
  • tolerant to lower grades of steel preparation for atmospheric exposure
  • excellent recoatability
  • cures down to 0°C with Low Temperature (LT) Part B
  • excellent abrasion resistance
  • resistant to splash of alkali, mineral oils, solvents and dilute acids
  • suitable for immersion in salt and fresh water
  • suitable for sewerage immersion applications such as wet wells and storage tanks (both for steel and concrete substrates)
  • can be applied to existing piling between tides or for new work
  • can be exposed to water immersion shortly after application
  • suitable with well-designed cathodic protection systems

Wattyl – Poly U400 – Polyureathane
Product Description:

  • a two pack recoatable isocyanate cured, acrylic polyurethane finish,
  • approved to APAS-1441/2, APAS-2911/1,
  • conforms to AS/NZS 3750.6 Type 1.

Principal Characteristics:

  • unlimited recoatability
  • excellent resistance to atmospheric exposure
  • excellent gloss retention
  • tough, flexible and abrasion resistant
  • resistant to splash of mineral oils, vegetable oils and aliphatic petroleum products
  • resistant to splash of mild chemicals

Jotun – SeaGuardian – Anti-Fouling

Product Description: Antifouling SeaGuardian is a tin free selfpolishing antifouling. IMO Anti-fouling System Convention compliant (AFS/CONF/26).

Intended Uses:As an antifouling on vessels operating in global service, with drydocking intervals up to 36 months.